Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands

Stems

Syntace Megaforce 2
$99.00
Syntace's Megafroce 2 stem is intended for all-mountain and downhill riding and comes in a range of sizes with a focus on torsional stiffness and weight savings. The 42mm wide bar clamp area stiffens up cockpits with bars wider than 700mm Titanium bolts help keep the weight low and strength high. - Stack height: 36mm - Weight: 132g (70mm)
Dimension 25.4mm Threadless Stem
$34.99
Dimension 25.4 Stem is a fully forged 6061-T6 aluminum stem with 4-bolt handlebar clamp. - 2-D forged AL-6061-T6 - Four-bolt handlebar clamp - 41mm height - Dimension stems are not intended for use with carbon handlebars or carbon steerer tubes - Weight: 130g-180g
Bontrager Elite Blendr Stem
$64.99
The Bontrager Elite Blendr Stem provides easy solutions for accessory integration. This alloy stem is light and strong, and it gives you endless options to integrate lights, a computer, and more with Blendr Elite accessory integration. - Seamless accessory integration with Blendr Elite - 6061-T6, 3D, forged alloy construction - 4-bolt dual band clamp retains stiffness and reduces weight - Opposing 2-bolt steerer tube clamp - Uses M5 countersunk, corrosion-resistant steel bolts with 5.2Nm torque spec - Approved for carbon bars and steerer tubes - Includes one Blendr base to integrate Ion lights and Trip computers
Ritchey Comp 4Axis Stem
$49.95
Ritchey's 4Axis Stem is crafted from 6061 aluminum for light weight and durability. It works with aluminum and carbon steerers thanks to the angled clamp design. And, the 4-bolt clamping system holds fast and works great with aluminum and carbon bars.
3T Arx II Pro
$79.99
3T's Arx II is a subtle refresh of the well-liked Arx alloy stem, which has found a place on every sort of bicycle since its launch in 2007. The faceplate is drawn in tighter at top and bottom for a more ovalized frontal appearance, while retaining the cutout 3T logo. The sides of the extension are slightly flattened for a more sculpted look by comparison with the tubular section of the first-generation Arx. A single M7 bolt clamps the stem to the fork steerer, instead of the twin M5 bolts previously used, and the Allen bolts used on the original Arx have been replaced by no-strip Torx bolts. - Stack height: 40mm - Weight: 135g (110mm)
Race Face Evolve
$39.99
A technically advanced design allows RaceFace's Evolve stem to handle trail and All Mountain riding at a very competitive weight. - Forged & blasted 6061 aluminum for high strength & fatigue resistance at a reasonable weight - Four bolt bar clamp holds bar securely in position - Interlocking U-Shaped Handlebar Clamp Geometry - Faceplate eliminates “stress risers” which could cause your bar to bend or break. This is particularly important for carbon bar users
ENVE M7 Mountain Stem 35mm
$280.00
A 35mm clamp diameter, gravity-rated, carbon-bodied mountain stem built for aggressive riding and the muscular look of today’s carbon Enduro and All-Mountain bikes. The M7 stem is designed to complement the look and ride feel of ENVE M7 handlebars. - Material: Carbon - Faceplate material: Aluminum - Hardware material: Titanium - Clamp Diameter: 35mm - Steerer Clamp Diameter: 1-1/8-inch - Torque Spec: 5.5Nm - Weight: 85g (35mm), 92g (50mm), 99g (65mm)
BOX Cusp Stem
$79.99
- 3-D forged from the finest 6061-T6 aluminum - Oversized clamp fits 35.0mm bars
FSA Energy SCR Stem
$104.00
At just 113g for a 100mm extension, the Energy stem represents cutting-edge aluminum construction. The shape is 3D-forged from 2014 aluminum for great strength, with the final refinements carried out by CNC machining. Titanium bolts complete the package. - Semi Integrated Cable routing (SCR) - 3D-Forged and CNC-machined from AL2014 - 4-bolt sculpted SL faceplate
Pro LT Stem
$39.99
the Pro LT stem is constructed of strong and lightweight anodized 6061 alloy, and features a headlock system for a secure front clamp fixation.
FSA Omega Road Stem
$29.99
FSA's Omega line is the perfect workhorse component group for the sport rider who wants race-winning technology and durability along with classic good looks. - 3D-forged and CNC-machined from AL6061/T6 - 4-bolt cold-forged face plate - Chromoly hardware - ±6° - 31.8mm handlebar clamp diameter - 35mm fork clamp stack height - 127 grams (100mm)
Profile Design Aris Road Stem (+/-25-degree rise)
$49.99
Profile's Aris stem is a no-nonsense stem made from 6061-aluminum that's been shot-peened and anodized for strength and durability. The 4-bolt face plate is stiff, ultra tough and makes handlebar changes a breeze. And, the opposing-bolt steerer clamp is safe and secure.
Dimension Trail Stem 35.0
$35.00
For cross country and all-mountain riding, Dimension Trail Stems provide a broad array of sizing options, rigorously tested to ISO 4210 Mountain standards. - Constructed with AL-6061-T6 aluminum - Shot-peened finish - Dimension stems are not intended for use with carbon handlebars or carbon steerer tubes
Ritchey Classic C-220 Stem
$59.95
You really can have it all; Ritchey's WCS C-220 stem features revolutionary stiffness and classically inspired good looks, but it’s quick and easy to install and remove thanks to a press-fit handlebar clamp interface and forward-facing hardware. The C-220 handlebar clamp design creates a more secure interface by wrapping a full 220 degrees over the handlebar. Bolt forces are aligned with the clamp so that the stem body ‘embraces’ the handlebar, which is less prone to damaging lightweight bars. This clamp design allows for a lighter faceplate and stem body with no sacrifice in strength or stiffness. The stem body is forged 2014 aluminum for further weight reduction. Premium quality chromoly steel bolts are used throughout. - Material: 3d forged 2014 alloy body - 4 x 4mm coated CrMo steel forward-facing faceplate bolts - 2 x 4mm coated CrMo steel offset steer tube clamp bolts - 5Nm torque max on all hardware - Compatible with all 31.8 bars - Press-fit clamp design installs and removes like a standard stem - Angle: 84/6 degree - Steerer Height: 42mm - Steerer diameter: 1-1/8" - Faceplate Width: 42mm - Silver Finish - 121g (110mm)
Paul Component Engineering Boxcar Stem
$141.00
The Boxcar Stem from Paul Components is the perfect combination of stiffness, strength, and reasonable weight. All screws are high-strength stainless steel with the popular T25 head. Made in Chico, California with US-sourced 2024 aircraft alloy. - Stack height: 36mm - Weight: 155g (90mm)
Thomson Elite X2 Road Stem
$99.95 - $114.95
Thomson's Elite X2 Road Stem is instantly recognizable because of Thomson's legendary style, and with strength to spare, this stem is more than just a pretty face. Made from a solid, one-piece block of 7000-series aluminum, the X2 combines exceptional strength with light weight for a stiff stem and total control on all your rides. It has a two-bolt clamp design that's just as strong as four-bolt designs thanks to Thomson's interlocking interface and it also cuts down on the weight. Plus, the stem's low 36mm stack height gives you more options for customizing your position. And, thanks to their reversible graphics, your X2 looks great whether you run a positive or negative rise.
ENVE Alloy Mountain Stem
$125.00
A 3D-forged, then precision-machined, lightweight, aluminum mountain bike stem in both 31.8mm and 35.0mm models rated for cross country, trail, all-mountain, enduro, and gravity applications. - Blind bolt holes and shaping - Cold-forged and precision-machined - No-gap face plate and clamp area - Stainless hardware
Velo Orange Tall-Stack Stem
$40.00
Save your steerer tube and eliminate headset spacers with the Velo Orange Tall-Stack alloy stem. It gives your bike's cockpit a nice clean look. Available in Polished or Black, the 17-degree angle allows the stem to be level on most modern frames. And, you can use handlebar clamp shims to adapt to smaller handlebar clamp diameters, if you like. - Stack height: 75mm - Not recommended for use with carbon steerer tubes
Ritchey Comp 4-Axis 44 Stem
$37.95
- Bar Clamp Diameter: 31.8mm - Material: Alloy - Stem Angle: +17 degrees, -17 degrees - S.H.I.S. Stem Clamp Diameter: 31.8mm
Ritchey WCS C220 Stem
$89.95
The WCS C220 stem is easy to install and remove thanks to a press-fit handlebar clamp interface and forward-facing hardware. - The handlebar clamp design creates a more secure interface by wrapping a full 220 degrees over the handlebar - Bolt forces are aligned with the clamp so that the stem body embraces the handlebar which is less prone to damaging lightweight bars - Clamp design allows for a lighter faceplate and stem body with no sacrifice in strength or stiffness
Fizik Cyrano R1 Stem
$119.99 - $120.00
Stems need to be light, simple, and rock solid. Fizik checked all the boxes with their Cyrano R1 Stem. The Cyrano stem forms an integral part of Fizik's Spine Concept fitting technology. A four-bolt face plate provides excellent torsional stiffness, and the choice of lengths and angles ensures that your perfect fit is out there.
Promax S-29 Stem
$41.00
Developed for longer-travel trail bikes, Promax's S-29 stem offers the perfect configuration to set you up for maximum comfort and control. Featuring an oversize extension tube and faceplate with massive clamping area, it’s sure to keep your bars stylishly in place through the most demanding terrain. These stems are cold-forged and CNC-machined from 6061-T6 aluminum for strength, low weight, and durability.
Redshift Sports ShockStop Stem
$149.99
An adjustable stiffness suspension stem that smooths out the ride by reducing the affects of impacts and road vibrations. - Unwanted vertical movement is absorbed by twin interchangeable elastomers - Stem retains torsional rigidity - Travel is limited to 1-2 centimeters - Made with 6061-T6 Aluminum - Includes 5 swappable elastomers (2 pre-installed, 3 additional) to customize the ride feel for your bike, weight, and riding style
Ritchey WCS Trail Stem
$89.95
The Ritchey WCS Trail Stem represents Ritchey's first stem specifically designed for today's 5-6-inch travel trail bikes using wide bars. More than just a beefed-up version of other stems, with the Trail stem we revised the patented C260 clamp to a 220-degree version that fits a wider variety of riser bar bends and still packs a dramatic increase in stiffness and strength over competitor's designs. Using 3D Forged 2014 alloy, the WCS Trail Stem serves up superior strength while remaining lightweight. The extra-wide bar clamp takes stiffness to the next level, fits most riser bars, and ensures plenty of confident control out on the trail. - Material: 3D Forged 2014 alloy - Angle: Zero rise - Steerer Height: 45mm - Faceplate Width: 40mm - Steerer: 1-1/8” - Ritchey Blatte finish - 115g (70mm)
Promax DA-1 Stem
$69.99
Promax's DA-1 XC mountain bike stem is 3D cold-forged, then CNC-machined from 6061-T6 aluminum to create a lightweight and strong stem. The two-piece faceplate features their bar-gripping DWT (Dynalock Web Technology), which increases the bar/stem interface.
Easton EA90
$94.99 - $99.99
Easton’s lightest aluminum stem is the choice of road racers and top XC pilots alike. The advanced EA90 aluminum tubing and 3D forging process results in a perfect blend of strength and weight. Easton’s patented DST distributes clamping forces more evenly over a larger area, making it the perfect stem for today’s lightweight aluminum and carbon handlebars. - Finish: Black Ano - Weight: 130g (100mm) - Rise: Varies - Clamp diameter: 31.8mm - Steerer: 1 1/8-inch - Length: 80mm, 90mm, 100mm, 110mm, 120mm, 130mm - Materials: EA90 alloy
Promax Impact Stem
$69.99
The Impact is Promax's top-load BMX stem. They come in 48-, 53-, and 60-millimeter extensions and are cold-forged from the highest quality 6061-T6 aluminum then CNC-machined to refine the shape and further reduce weight. The “open” design keeps weight low while maintaining plenty of strength and ensuring your bars stay put. - Weight: 9.8oz. - Stack height: 30.5mm
FSA NS ACR Road Stem
$115.00
FSA ACR (Aerodynamic Cable Routing) Stems have a low-profile frontal area that is suitable for road and gravel riding. - Aerodynamic Cable Routing (ACR) - Low-profile frontal area - No rotation limit - Body and faceplate - 6061 T6 - Chromoly hardware - Specific frame and headset required - 31.8mm handlebar clamp diameter - 30mm fork clamp stack height - Compatible with: K-Force Light ACR Compact, SL-K ACR Compact, Energy ACR Compact, K-Wing AGX and K-Wing AGX handlebars
Pro Vibe Stem
$129.99
Some might call it magic—PRO likes to refer to it as co-creation: aligning all forces to work in favor of you. The PRO Vibe Stem is designed to align your cockpit perfectly with your bike for an optimal riding position. Supreme stiffness offers you more control during those high-speed descents or maneuvers. It's also developed for ultimate integration with Di2 to give you maximum aerodynamic performance and ultra-clean styling. With the specially positioned cable ports, you can internally route Shimano Di2 cables. All of the advantages of Di2, with none of the cables showing. Align yourself with performance—use the PRO Vibe Stem. - Anodized AL-7075 - Shimano DI2 integration - Lightweight titanium bolts - Integrated topcap
Ritchey WCS Carbon Matrix C220 84D Stem
$159.95
You really can have it all—the new WCS C220 stem rivals the performance of the revolutionary C260 stem design, but it's quicker and easier to install and remove, thanks to a press-fit handlebar clamp interface and forward-facing hardware. First proven on the Ritchey TRAIL stem, the C220 handlebar clamp design creates a more secure interface by wrapping a full 220-degrees over the handlebar. Bolt forces are aligned with the clamp so that the stem body 'embraces' the handlebar, which is less prone to damaging lightweight bars. This clamp design allows for a lighter faceplate and stem body with no sacrifice in strength or stiffness. The Carbon Matrix stem body is forged 7075 aluminum with a stiffness-enhancing carbon exoskeleton which makes this 12% stiffer than the WCS alloy C220 stem. Premium quality CRMO steel bolts are used throughout. - Material: 3D forged 7075, carbon encased body - 4 x 4mm coated CrMo steel forward-facing faceplate bolts - 2 x 4mm coated CrMo steel offset steer tube clamp bolts - 5Nm torque max on all hardware - Compatible with all 31.8 bars - Press-fit clamp design installs and removes like a standard stem - Angle: 84/6 degree - Steerer Height: 42mm - Steerer: 1-1/8” - Faceplate Width: 42mm - Matte UD carbon finish - 126g (110mm)
Page 1 of 4 Next page